From 0a8fef3915340ddb17d684f0ae12d3ea53a292bf Mon Sep 17 00:00:00 2001
From: timmmooney <mooney@aps.anl.gov>
Date: Mon, 1 Dec 2014 22:47:30 +0000
Subject: [PATCH]
---
iocBoot/iocLinux/softGlue.cmd | 204 ++++++++++++++++++++++++++++++++++
1 file changed, 204 insertions(+)
create mode 100644 iocBoot/iocLinux/softGlue.cmd
diff --git a/iocBoot/iocLinux/softGlue.cmd b/iocBoot/iocLinux/softGlue.cmd
new file mode 100644
index 0000000..1f2e4ba
--- /dev/null
+++ b/iocBoot/iocLinux/softGlue.cmd
@@ -0,0 +1,204 @@
+# BEGIN softGlue.cmd ----------------------------------------------------------
+# This must run after industryPack.cmd
+
+#devAsynSoftGlueDebug=1
+#drvIP_EP201Debug=1
+
+################################################################################
+# Initialize the FPGA
+#-----------------------
+# Write content to the FPGA. This command will fail if the FPGA already
+# has content loaded, as it will after a soft reboot. To load new FPGA
+# content, you must power cycle the ioc.
+#
+# initIP_EP200_FPGA(ushort carrier, ushort slot, char *filename)
+# carrier: IP-carrier number (numbering begins at 0)
+# slot: IP-slot number (numbering begins at 0)
+# filename: Name of the FPGA-content hex file to load into the FPGA.
+#
+
+# standard softGlue 2.2
+#initIP_EP200_FPGA(0, 2, "$(SOFTGLUE)/softGlueApp/Db/SoftGlue_2_2.hex")
+# standard softGlue 2.2 plus two shift registers
+#initIP_EP200_FPGA(0, 2, "$(SOFTGLUE)/softGlueApp/Db/SoftGlue_2_2_Octupole_0_0.hex")
+# standard softGlue 2.2 plus two up/down counters
+#initIP_EP200_FPGA(0, 2, "$(SOFTGLUE)/softGlueApp/Db/SoftGlue_2_2_1ID_Vgate_0_1.hex")
+# standard softGlue 2.2 plus two up/down counters plus two quadrature decoders
+initIP_EP200_FPGA(0, 2, "$(SOFTGLUE)/softGlueApp/Db/SoftGlue_2_2_Encoder.hex")
+
+################################################################################
+# Initialize basic field I/O
+#------------------------------
+# int initIP_EP200(ushort carrier, ushort slot, char *portName1,
+# char *portName2, char *portName3, int sopcBase)
+# carrier: IP-carrier number (numbering begins at 0)
+# slot: IP-slot number (numbering begins at 0)
+# portName1: Name of asyn port for component at sopcBase
+# portName2: Name of asyn port for component at sopcBase+0x10
+# portName3: Name of asyn port for component at sopcBase+0x20
+# sopcBase: must agree with FPGA content (0x800000)
+initIP_EP200(0, 2, "SGIO_1", "SGIO_2", "SGIO_3", 0x800000)
+
+################################################################################
+# Initialize field-I/O interrupt support
+#------------------------------------------
+# int initIP_EP200_Int(ushort carrier, ushort slot, int intVectorBase,
+# int risingMaskMS, int risingMaskLS, int fallingMaskMS,
+# int fallingMaskLS)
+# carrier: IP-carrier number (numbering begins at 0)
+# slot: IP-slot number (numbering begins at 0)
+# intVectorBase: must agree with the FPGA content loaded (0x90 for softGlue
+# 2.1 and higher; 0x80 for softGlue 2.0 and lower). softGlue
+# uses three vectors, for example, 0x90, 0x91, 0x92.
+# risingMaskMS: interrupt on 0->1 for I/O pins 33-48
+# risingMaskLS: interrupt on 0->1 for I/O pins 1-32
+# fallingMaskMS: interrupt on 1->0 for I/O pins 33-48
+# fallingMaskLS: interrupt on 1->0 for I/O pins 1-32
+initIP_EP200_Int(0, 2, 0x90, 0x0, 0x0, 0x0, 0x0)
+
+################################################################################
+# Set field-I/O data direction
+#--------------------------------
+# int initIP_EP200_IO(ushort carrier, ushort slot, ushort moduleType,
+# ushort dataDir)
+# carrier: IP-carrier number (numbering begins at 0)
+# slot: IP-slot number (numbering begins at 0)
+# moduleType: one of [201, 202, 203, 204]
+# dataDir: Bit mask, in which only the first 9 bits are significant. The
+# meaning of each bit depends on moduleType, as shown in the
+# table below. If a bit is set, the corresponding field I/O pins
+# are outputs. Note that for the 202 and 204 modules, all I/O
+# is differential, and I/O pin N is paired with pin N+1. For the
+# 203 module, pins 25/26 through 47/48 are differential pairs.
+#
+# -------------------------------------------------------------------
+# | Correspondence between dataDir bits (0-8) and I/O pins (1-48) |
+# -------------------------------------------------------------------
+# | | 201 | 202/204 | 203 |
+# -------------------------------------------------------------------
+# | bit 0 | pins 1-8 | pins 1, 3,25,27 | pins 25,27 |
+# | bit 1 | pins 9-16 | pins 5, 7,29,31 | pins 29,31 |
+# | bit 2 | pins 17-24 | pins 9,11,33,35 | pins 33,35 |
+# | bit 3 | pins 25-32 | pins 13,15,37,39 | pins 37,39 |
+# | | | | |
+# | bit 4 | pins 33-40 | pins 17,19,41,43 | pins 41,43 |
+# | bit 5 | pins 41-48 | pins 21,23,45,47 | pins 45,47 |
+# | bit 6 | x | x | pins 1-8 |
+# | bit 7 | x | x | pins 9-16 |
+# | | | | |
+# | bit 8 | x | x | pins 17-24 |
+# -------------------------------------------------------------------
+# Examples:
+# 1. For the IP-EP201, moduleType is 201, and dataDir == 0x3c would mean
+# that I/O bits 17-48 are outputs.
+# 2. For the IP-EP202 (IP-EP204), moduleType is 202(204), and dataDir == 0x13
+# would mean that I/O bits 1,3,25,27, 5,7,29,31, 17,19,41,43 are outputs.
+# 3. For the IP-EP203, moduleType is 203, and dataDir == 0x??? would mean
+# that I/O bits 1-8, 25,27, 29,31, 33,35, 45,47 are outputs.
+#initIP_EP200_IO(0, 2, 201, 0x3c)
+initIP_EP200_IO(0, 2, 201, 0xc)
+#initIP_EP200_IO(0, 2, 202, 0x13)
+
+#-------------------------------------------------------------------------------
+# For backward compatibility with softGlue 2.1 and earlier, the following
+# command can be used to initialize an IP_EP201 module, instead of the
+# above calls to initIP_EP200(), initIP_EP200_Int(), and initIP_EP200_IO().
+# This won't work for any other IP_EP200 module
+#
+# int initIP_EP201(char *portName, ushort carrier, ushort slot,
+# int msecPoll, int dataDir, int sopcOffset, int interruptVector,
+# int risingMask, int fallingMask)
+# portName: Name of asyn port for component at sopcOffset
+# carrier: IP-carrier number (numbering begins at 0)
+# slot: IP-slot number (numbering begins at 0)
+# msecPoll: Time interval between driver polls of field I/O bits
+# dataDir: Data direction for I/O bits, explained below.
+# sopcOffset: SOPC offset (must be as in example below).
+# interruptVector: Must agree with the FPGA content loaded (0x90, 0x91,
+# 0x92 for softGlue 2.1 and higher; 0x80, 0x81, 0x82 for
+# softGlue 2.0 and lower).
+# risingMask: 16-bit mask: if a bit is 1, the corresponding I/O bit will
+# generate an interrupt when its value goes from 0 to 1.
+# Bit 0 corresponds to field I/O pin 1, bit 1 to pin 2, etc.
+# fallingMask: Similar to risingMask, but for 1-to-0 transitions.
+#
+# Note that the user can overwrite risingMask and
+# fallingMask at run time, with menu selections, and
+# probably has those selections autosaved.
+# dataDir is a bit mask in which only bits 0 and 8 are significant.
+# for sopcOffset 0x800000
+# If bit 0 of dataDir is set, I/O bits 1-8 are outputs.
+# If bit 8 of dataDir is set, I/O bits 9-16 are outputs.
+# for sopcOffset 0x800010
+# If bit 0 of dataDir is set, I/O bits 17-24 are outputs.
+# If bit 8 of dataDir is set, I/O bits 25-32 are outputs.
+# for sopcOffset 0x800020
+# If bit 0 of dataDir is set, I/O bits 33-40 are outputs.
+# If bit 8 of dataDir is set, I/O bits 41-48 are outputs.
+#!initIP_EP201("SGIO_1",0,2,1000000,0x101,0x800000,0x90,0x00,0x00)
+#!initIP_EP201("SGIO_2",0,2,1000000,0x101,0x800010,0x91,0x00,0x00)
+#!initIP_EP201("SGIO_3",0,2,1000000,0x101,0x800020,0x92,0x00,0x00)
+
+################################################################################
+# Initialize softGlue signal-name support
+#-------------------------------------------
+# All instances of a single-register component are initialized with a single
+# call, as follows:
+#
+#initIP_EP201SingleRegisterPort(char *portName, ushort carrier, ushort slot)
+#
+# For example:
+# initIP_EP201SingleRegisterPort("SOFTGLUE", 0, 2)
+initIP_EP201SingleRegisterPort("SOFTGLUE", 0, 2)
+
+
+################################################################################
+# Load databases
+#------------------
+# Load a single database that all database fragments supporting
+# single-register components can use to show which signals are connected
+# together. This database is not needed for the functioning of the
+# components, it's purely for the user interface.
+dbLoadRecords("$(SOFTGLUE)/db/softGlue_SignalShow.db","P=xxx:,H=softGlue:,PORT=SOFTGLUE,READEVENT=10")
+
+# Load a set of database fragments for each single-register component.
+# This database contains the records for standard softGlue, and must be loaded
+# for all .hex files above
+dbLoadRecords("$(SOFTGLUE)/db/softGlue_FPGAContent.db", "P=xxx:,H=softGlue:,PORT=SOFTGLUE,READEVENT=10")
+
+# This database contains the additional records needed for
+# SoftGlue_2_2_Octupole_0_0.hex
+#!dbLoadRecords("$(SOFTGLUE)/db/softGlue_FPGAContent_octupole.db", "P=xxx:,H=softGlue:,PORT=SOFTGLUE,READEVENT=10")
+
+# This database contains the additional records needed for
+# SoftGlue_2_2_1ID_Vgate_0_1.hex
+#dbLoadRecords("$(SOFTGLUE)/db/softGlue_FPGAContent_s1ID_Vgate.db", "P=xxx:,H=softGlue:,PORT=SOFTGLUE,READEVENT=10")
+
+# This database contains the additional records needed for
+# SoftGlue_2_2_Encoder.hex
+dbLoadRecords("$(SOFTGLUE)/db/softGlue_FPGAContent_Encoder.db", "P=xxx:,H=softGlue:,PORT=SOFTGLUE,READEVENT=10")
+
+# Interrupt support.
+# ('putenv' is used to fit the command into the vxWorks command line space.)
+putenv "SFDB=$(SOFTGLUE)/db/softGlue_FPGAInt.db"
+dbLoadRecords("$(SFDB)","P=xxx:,H=softGlue:,PORT1=SGIO_1,PORT2=SGIO_2,PORT3=SGIO_3,FIFO=10")
+
+taskDelay(50)
+
+# Some stuff just for convenience: software clock and pulse generators, and
+# a couple of busy records.
+dbLoadRecords("$(SOFTGLUE)/db/softGlue_convenience.db", "P=xxx:,H=softGlue:")
+
+# configMenu Menu of softGlue circuits
+dbLoadRecords("$(AUTOSAVE)/asApp/Db/configMenu.db","P=xxx:,CONFIG=SG")
+# Note that the request file MUST be named $(CONFIG)Menu.req. If the macro
+# CONFIGMENU is defined with any value, backup (".savB") and sequence files
+# (".savN") will not be written. We don't want these for configMenu.
+doAfterIocInit("create_manual_set('SGMenu.req','P=xxx:,CONFIG=SG,H=softGlue:,CONFIGMENU=1')")
+
+# Register included example of a custom softGlue interrupt-service routine.
+# This is for interrupts that occur too closely spaced in time for softGlue's
+# normal interrupt service (an output link to an EPICS record) to handle.
+#sampleCustomInterruptPrepare(0, 2, 0x800010, 0x1)
+
+# END softGlue.cmd ------------------------------------------------------------
--
GitLab