diff --git a/iocBoot/iocvxWorks/st.cmd b/iocBoot/iocvxWorks/st.cmd
index 4acf77b9daca44f37fb248f98599e8a9cad8ba0a..1de9f3f99c948708c314e2322f185cba6df43b68 100644
--- a/iocBoot/iocvxWorks/st.cmd
+++ b/iocBoot/iocvxWorks/st.cmd
@@ -10,7 +10,6 @@ location="Earth"
cd ""
< ../nfsCommands
< cdCommands
-< MPFconfig.cmd
################################################################################
cd topbin
@@ -23,23 +22,13 @@ sysCplusEnable=1
# allocate enough memory here to force code to load in lower 32 MB.
mem = malloc(1024*1024*96)
-### Load custom EPICS software from user tree and from share
+### Load synApps EPICS software
ld < xxx.munch
cd startup
-recDynLinkDebug = 1
-
# Increase size of buffer for error logging from default 1256
-errlogInit(5000)
-
-# Note that you need an MPF router not only for IP modules, but also for
-# the AIM MCA support and other MPF servers
-routerInit
-localMessageRouterStart(0)
-
-# This IOC configures the MPF server code locally
-#< st_mpfserver.cmd
+errlogInit(20000)
# override address, interrupt vector, etc. information in module_types.h
#module_types()
@@ -63,111 +52,27 @@ iocxxxVX_registerRecordDeviceDriver(pdbbase)
# See also create_monitor_set(), after iocInit() .
< save_restore.cmd
-##############################################################################
+# Industry Pack support
+#< industryPack.cmd
-# Insertion-device control
-dbLoadRecords("$(STD)/stdApp/Db/IDctrl.db","P=xxx:,xx=02us")
+# VME devices
+#< vme.cmd
-###############################################################################
+# CAMAC hardware
+#<camac.cmd
-##### Motors (see motors.substitutions in same directory as this file) ####
+# Motors
#dbLoadTemplate("basic_motor.substitutions")
dbLoadTemplate("motor.substitutions")
-# OMS VME driver setup parameters:
-# (1)cards, (2)axes per card, (3)base address(short, 16-byte boundary),
-# (4)interrupt vector (0=disable or 64 - 255), (5)interrupt level (1 - 6),
-# (6)motor task polling rate (min=1Hz,max=60Hz)
-omsSetup(2, 8, 0xFC00, 180, 5, 10)
-
-# OMS VME58 driver setup parameters:
-# (1)cards, (2)axes per card, (3)base address(short, 4k boundary),
-# (4)interrupt vector (0=disable or 64 - 255), (5)interrupt level (1 - 6),
-# (6)motor task polling rate (min=1Hz,max=60Hz)
-oms58Setup(3, 8, 0x4000, 190, 5, 10)
-
-# Highland V544 driver setup parameters:
-# (1)cards, (2)axes per card, (3)base address(short, 4k boundary),
-# (4)interrupt vector (0=disable or 64 - 255), (5)interrupt level (1 - 6),
-# (6)motor task polling rate (min=1Hz,max=60Hz)
-#v544Setup(0, 4, 0xDD00, 0, 5, 10)
-
-# Newport MM4000 driver setup parameters:
-# (1) max. controllers, (2)Unused, (3)polling rate (min=1Hz,max=60Hz)
-#MM4000Setup(3, 0, 10)
-
-# Newport MM4000 driver configuration parameters:
-# (1)controller# being configured,
-# (2)port type: 0-GPIB_PORT or 1-RS232_PORT,
-# (3)GPIB link or MPF server location
-# (4) GPIB address (int) or mpf serial server name (string)
-#MM4000Config(0, 1, 0, "serial2")
-
-# Newport PM500 driver setup parameters:
-# (1) maximum number of controllers in system
-# (2) maximum number of channels on any controller
-# (3) motor task polling rate (min=1Hz,max=60Hz)
-#PM500Setup(1, 3, 10)
-
-# Newport PM500 configuration parameters:
-# (1) card being configured
-# (2) port type (0-GPIB_PORT, 1-RS232_PORT)
-# (3) GPIB link or MPF server location
-# (4) GPIB address (int) or mpf serial server name (string)
-#PM500Config(0, 1, 0, "serial3")
-
-# McClennan PM304 driver setup parameters:
-# (1) maximum number of controllers in system
-# (2) maximum number of channels on any controller
-# (3) motor task polling rate (min=1Hz, max=60Hz)
-#PM304Setup(1, 1, 10)
-
-# McClennan PM304 driver configuration parameters:
-# (1) controller being configured
-# (2) MPF server location
-# (3) MPF serial server name (string)
-#PM304Config(0, 0, "serial4")
-
-# ACS MCB-4B driver setup parameters:
-# (1) maximum number of controllers in system
-# (2) maximum number of axes per controller
-# (3) motor task polling rate (min=1Hz, max=60Hz)
-#MCB4BSetup(1, 4, 10)
-
-# ACS MCB-4B driver configuration parameters:
-# (1) controller being configured
-# (2) MPF server location
-# (3) MPF server name (string)
-#MCB4BConfig(0, 0, "serial5")
-
-##### Pico Motors (Ernest Williams MHATT-CAT)
-##### Motors (see picMot.substitutions in same directory as this file) ####
-#dbLoadTemplate("picMot.substitutions")
-
-###############################################################################
-
-### Scalers: Joerger VSC8/16
-#dbLoadRecords("$(VME)/vmeApp/Db/Jscaler.db","P=xxx:,S=scaler1,C=0")
-dbLoadRecords("$(STD)/stdApp/Db/scaler.db","P=xxx:,S=scaler1,C=0,DTYP=Joerger VSC8/16,FREQ=10000000")
-# Joerger VSC setup parameters:
-# (1)cards, (2)base address(ext, 256-byte boundary),
-# (3)interrupt vector (0=disable or 64 - 255)
-VSCSetup(1, 0xB0000000, 200)
-
-# Joerger VS
-# scalerVS_Setup(int num_cards, /* maximum number of cards in crate */
-# char *addrs, /* address (0x800-0xf800, 2048-byte (0x800) boundary) */
-# unsigned vector, /* valid vectors(64-255) */
-# int intlevel)
-scalerVS_Setup(1, 0x2000, 205, 5)
-#devScaler_VSDebug=0
-dbLoadRecords("$(STD)/stdApp/Db/scaler.db","P=xxx:,S=scaler3,C=0, DTYP=Joerger VS, FREQ=10000000")
-
### Allstop, alldone
# This database must agree with the motors and other positioners you've actually loaded.
# Several versions (e.g., all_com_32.db) are in stdApp/Db
dbLoadRecords("$(STD)/stdApp/Db/all_com_16.db","P=xxx:")
+### Insertion-device control
+dbLoadRecords("$(STD)/stdApp/Db/IDctrl.db","P=xxx:,xx=02us")
+
### Scan-support software
# crate-resident scan. This executes 1D, 2D, 3D, and 4D scans, and caches
# 1D data, but it doesn't store anything to disk. (See 'saveData' below for that.)
@@ -212,15 +117,6 @@ dbLoadRecords("$(OPTICS)/opticsApp/Db/kohzuSeq.db","P=xxx:,M_THETA=m9,M_Y=m10,M_
# modified geometry (geometry 2)
dbLoadRecords("$(OPTICS)/opticsApp/Db/kohzuSeq.db","P=xxx:,M_THETA=m9,M_Y=m10,M_Z=m11,yOffLo=4,yOffHi=36")
-# Heidenhain ND261 encoder (for PSL monochromator)
-#dbLoadRecords("$(IP)/ipApp/Db/heidND261.db", "P=xxx:,C=0,SERVER=serial1")
-
-# Heidenhain IK320 VME encoder interpolator
-#dbLoadRecords("$(VME)/vmeApp/Db/IK320card.db","P=xxx:,sw2=card0:,axis=1,switches=41344,irq=3")
-#dbLoadRecords("$(VME)/vmeApp/Db/IK320card.db","P=xxx:,sw2=card0:,axis=2,switches=41344,irq=3")
-#dbLoadRecords("$(VME)/vmeApp/Db/IK320group.db","P=xxx:,group=5")
-#drvIK320RegErrStr()
-
# Spherical grating monochromator
dbLoadRecords("$(OPTICS)/opticsApp/Db/SGM.db","P=xxx:,N=1,M_x=m7,M_rIn=m6,M_rOut=m8,M_g=m9")
@@ -228,138 +124,14 @@ dbLoadRecords("$(OPTICS)/opticsApp/Db/SGM.db","P=xxx:,N=1,M_x=m7,M_rIn=m6,M_rOut
dbLoadRecords("$(OPTICS)/opticsApp/Db/hrSeq.db","P=xxx:,N=1,M_PHI1=m9,M_PHI2=m10")
#dbLoadRecords("$(OPTICS)/opticsApp/Db/hrSeq.db","P=xxx:,N=2,M_PHI1=m11,M_PHI2=m12")
-### Canberra AIM Multichannel Analyzer ###
-#mcaRecordDebug=1
-#devMcaMpfDebug=1
-#mcaAIMServerDebug=1
-#aimDebug=1
-#icbDebug=1
-#icbServerDebug=1
-#icbDspDebug=1
-#icbTcaDebug=1
-
-# AIMConfig(char *serverName, int etherAddr, int port, int maxChans,
-# int maxSignals, int maxSequences, char *etherDev, int queueSize)
-#
-# serverName: defined here, must agree with dbLoadRecords command
-# etherAddr: ethernet address of AIM module
-# port: Which ADC port of the AIM module does this config involve? [1,2]
-# maxChans: Histogram bins per signal per sequence. (If a multiplexor or
-# MCS module is in use, this must agree with hardware setting.)
-# maxSignals: How many signals (multiplexed ADC inputs)? (If a multiplexor
-# or MCS module is in use, this must agree with hardware setting.)
-# maxSequences: How many sequences (usually, a sequence is a "time slice")?
-# etherDev: vxWorks device used to communicate over the network to AIM.
-# Typically "ei0" for mv16x, mv17x; "dc0" for Motorola PowerPC
-# queueSize: size of MPF message queue for this server (100 should be plenty)
-#
-# EXAMPLE:
-# AIMConfig("AIM1/2", 0x9AA, 2, 2048, 1, 1, "dc0", 100)
-
-AIMConfig("AIM1/2", 0x9AA, 2, 4000, 1, 1, "dc0", 100)
-
-dbLoadRecords("$(MCA)/mcaApp/Db/mca.db","P=xxx:,M=mca1,INP=#C0 S0 @AIM1/2,DTYPE=MPF MCA,NCHAN=4000")
-
-# Initialize ICB software, and create a new ICB server
-# icbSetup(const char *serverName, int maxModules, int queueSize)
-#
-# serverName: defined here, must agree with icbConfig and dbLoadRecords commands
-# maxModules: Maximum number of ICB modules that this server will control
-# queueSize: size of MPF message queue for this server (100 should be plenty)
-icbSetup("icb/1", 10, 100)
-
-# Configure an ICB module on this server
-# icbConfig(const char *serverName, int module, int etherAddr, int icbAddress)
-#
-# serverName: defined in icbSetup above
-# module: the index number for this module (0,1,2...)
-# etherAddr: ethernet address of AIM module
-# icbAddress: ICB address of this module (set with internal rotary switch, 0x0-0xF)
-icbConfig("icb/1", 0, 0x9AA, 3)
-
-# In dbLoadRecords commands for ICB devices
-# CARD = (0,1) for (local/remote),
-# SERVER = server name supplied as argument to icbConfig(),
-# ADDR = module number supplied as argument to icbConfig()
-
-dbLoadRecords("$(MCA)/mcaApp/Db/icb_adc.db","P=xxx:,ADC=icbAdc1,CARD=0,SERVER=icb/1,ADDR=0")
-
-#icbConfig("icb/1", 1, 0x9AA, 2)
-#dbLoadRecords("$(MCA)/mcaApp/Db/icb_hvps.db","P=xxx:,HVPS=icbHvps1,CARD=0,SERVER=icb/1,ADDR=1")
-
-#icbConfig("icb/1", 2, 0x9AA, 3)
-#dbLoadRecords("$(MCA)/mcaApp/Db/icb_amp.db","P=xxx:,AMP=icbAmp1,CARD=0,SERVER=icb/1,ADDR=2")
-
-# icbTcaSetup(char *serverName, int maxModules, int queueSize)
-#
-# serverName: defined here, must agree with icbTcaConfig and dbLoadRecords commands
-# maxModules: Maximum number of TCA modules that this server will control
-# queueSize: size of MPF message queue for this server (100 should be plenty)
-
-#icbTcaSetup("icbTca/1", 3, 100)
-
-# icbTcaConfig(char *serverName, int module, int etherAddr, int icbAddress)
-#
-# serverName: defined in icbTcaSetup above
-# module: the index number for this module (0,1,2...)
-# etherAddr: ethernet address of AIM module
-# icbAddress: ICB address of this module (set with internal rotary switch, 0x0-0xF)
-
-#icbTcaConfig("icbTca/1", 0, 0x9AA, 4)
-#dbLoadRecords("$(MCA)/mcaApp/Db/icb_tca.db","P=xxx:,TCA=icbTca1,MCA=mca1,CARD=0,SERVER=icbTca/1,ADDR=0")
-
-# icbDspSetup(char *serverName, int maxModules, int queueSize)
-#
-# serverName: defined here, must agree with icbDspConfig and dbLoadRecords commands
-# maxModules: Maximum number of DSP 9660 modules that this server will control
-# queueSize: size of MPF message queue for this server (100 should be plenty)
-
-#icbDspSetup("icbDsp/1", 3, 100)
-
-# icbDspConfig(char *serverName, int module, int etherAddr, int icbAddress)
-#
-# serverName: defined in icbDspSetup above
-# module: the index number for this module (0,1,2...)
-# etherAddr: ethernet address of AIM module
-# icbAddress: ICB address of this module (set with internal rotary switch, 0x0-0xF)
-
-#icbDspConfig("icbDsp/1", 0, 0x9AA, 5)
-#dbLoadRecords("$(MCA)/mcaApp/Db/icbDsp.db", "P=xxx:,DSP=dsp1,CARD=0,SERVER=icbDsp/1,ADDR=0")
+# Load single element Canberra AIM MCA and ICB modules
+< canberra_1.cmd
# Load 13 element detector software
-#< 13element.cmd
+#< canberra_13.cmd
# Load 3 element detector software
-#< 3element.cmd
-
-### Struck 7201 multichannel scaler (same as SIS 3806 multichannel scaler)
-
-#mcaRecordDebug = 10
-#devSTR7201Debug = 10
-#drvSTR7201Debug = 10
-
-dbLoadRecords("$(MCA)/mcaApp/Db/Struck8.db","P=xxx:mcs:")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca1,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S0 @,CHANS=1000")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca2,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S1 @,CHANS=1000")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca3,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S2 @,CHANS=1000")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca4,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S3 @,CHANS=1000")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca5,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S4 @,CHANS=1000")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca6,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S5 @,CHANS=1000")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca7,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S6 @,CHANS=1000")
-dbLoadRecords("$(MCA)/mcaApp/Db/simple_mca.db","P=xxx:mcs:,M=mca8,DTYP=Struck STR7201 MCS,PREC=3,INP=#C0 S7 @,CHANS=1000")
-
-# STR7201Setup(int numCards, int baseAddress, int interruptVector, int interruptLevel)
-STR7201Setup(2, 0x90000000, 220, 6)
-# STR7201Config(int card, int maxSignals, int maxChans, int 1=enable internal 25MHZ clock)
-STR7201Config(0, 8, 1000, 0)
-
-# Struck as EPICS scaler
-#dbLoadRecords("$(MCA)/mcaApp/Db/STR7201scaler.db", "P=xxx:,S=scaler2,C=0")
-dbLoadRecords("$(STD)/stdApp/Db/scaler.db","P=xxx:,S=scaler2,C=0,DTYP=Struck STR7201 Scaler,FREQ=25000000")
-
-### Acromag IP330 in sweep mode ###
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=mADC_1,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S0 @Ip330Sweep1")
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=mADC_2,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S1 @Ip330Sweep1")
+#< canberra_3.cmd
### Stuff for user programming ###
dbLoadRecords("$(CALC)/calcApp/Db/userCalcs10.db","P=xxx:")
@@ -379,38 +151,6 @@ dbLoadRecords("$(CALC)/calcApp/Db/interp.db", "P=xxx:,N=2000")
# array test
dbLoadRecords("$(CALC)/calcApp/Db/arrayTest.db", "P=xxx:,N=2000")
-### serial support ###
-
-# generic serial ports
-#dbLoadRecords("$(IP)/ipApp/Db/generic_serial.db", "P=xxx:,C=0,SERVER=serial1")
-
-# serial O/I block (generic serial record with format and parse string calcs)
-# on epics/mpf processor
-#dbLoadRecords("$(IP)/ipApp/Db/serial_OI_block.db","P=xxx:,N=0_1,C=0,SERVER=serial5")
-# on stand-alone mpf processor
-#dbLoadRecords("$(IP)/ipApp/Db/serial_OI_block.db","P=xxx:,N=1_1,C=0,SERVER=serial5")
-
-# Stanford Research Systems SR570 Current Preamplifier
-#dbLoadRecords("$(IP)/ipApp/Db/SR570.db", "P=xxx:,A=A1,C=0,SERVER=serial1")
-
-# Lakeshore DRC-93CA Temperature Controller
-#dbLoadRecords("$(IP)/ipApp/Db/LakeShoreDRC-93CA.db", "P=xxx:,Q=TC1,C=0,SERVER=serial4")
-
-# Huber DMC9200 DC Motor Controller
-#dbLoadRecords("$(IP)/ipApp/Db/HuberDMC9200.db", "P=xxx:,Q=DMC1:,C=0,SERVER=serial5")
-
-# Oriel 18011 Encoder Mike
-#dbLoadRecords("$(IP)/ipApp/Db/eMike.db", "P=xxx:,M=em1,C=0,SERVER=serial3")
-
-# Keithley 2000 DMM
-#dbLoadRecords("$(IP)/ipApp/Db/Keithley2kDMM_mf.db","P=xxx:,Dmm=D1,C=0,SERVER=serial1")
-
-# Oxford Cyberstar X1000 Scintillation detector and pulse processing unit
-#dbLoadRecords("$(IP)/ipApp/Db/Oxford_X1k.db","P=xxx:,S=s1,C=0,SERVER=serial4")
-
-# Oxford ILM202 Cryogen Level Meter (Serial)
-#dbLoadRecords("$(IP)/ipApp/Db/Oxford_ILM202.db","P=xxx:,S=s1,C=0,SERVER=serial5")
-
### GPIB support ###
# GPIB O/I block (generic gpib record with format and parse string calcs)
#dbLoadRecords("$(IP)/ipApp/Db/GPIB_OI_block.db","P=xxx:,N=1,L=10")
@@ -421,218 +161,28 @@ dbLoadRecords("$(CALC)/calcApp/Db/arrayTest.db", "P=xxx:,N=2000")
# Keithley 199 DMM at GPIB address $(A)
#dbLoadRecords("$(STD)/stdApp/Db/KeithleyDMM.db", "P=xxx:,L=10,A=26")
-# generic gpib record
-#dbLoadRecords("$(STD)/stdApp/Db/gpib.db","P=xxx:")
-
-### Miscellaneous ###
-# Systran DAC database
-#dbLoadTemplate("dac128V.substitutions")
-
-# vme test record
-dbLoadRecords("$(VME)/vmeApp/Db/vme.db", "P=xxx:,Q=vme1")
-
-# Hewlett-Packard 10895A Laser Axis (interferometer)
-#dbLoadRecords("$(VME)/vmeApp/Db/HPLaserAxis.db", "P=xxx:,Q=HPLaser1, C=0")
-# hardware configuration
-# example: devHP10895LaserAxisConfig(ncards,a16base)
-#devHPLaserAxisConfig(2,0x1000)
-
-# Acromag general purpose Digital I/O
-#dbLoadRecords("$(VME)/vmeApp/Db/Acromag_16IO.db", "P=xxx:, A=1")
-
-# Acromag AVME9440 setup parameters:
-# devAvem9440Config (ncards,a16base,intvecbase)
-#devAvme9440Config(1,0x0400,0x78)
-
# Miscellaneous PV's, such as burtResult
dbLoadRecords("$(STD)/stdApp/Db/misc.db","P=xxx:")
#dbLoadRecords("$(STD)/stdApp/Db/VXstats.db","P=xxx:")
# vxStats
dbLoadTemplate("vxStats.substitutions")
-# Elcomat autocollimator
-#dbLoadRecords("$(IP)/ipApp/Db/Elcomat.db", "P=xxx:,C=0,SERVER=serial8")
-
-# Bunch-clock generator
-#dbLoadRecords("$(VME)/vmeApp/Db/BunchClkGen.db","P=xxx:")
-#dbLoadRecords("$(VME)/vmeApp/Db/BunchClkGenA.db", "UNIT=xxx")
-# hardware configuration
-# example: BunchClkGenConfigure(intCard, unsigned long CardAddress)
-#BunchClkGenConfigure(0, 0x8c00)
-
### Queensgate piezo driver
#dbLoadRecords("$(IP)/ipApp/Db/pzt_3id.db","P=xxx:")
#dbLoadRecords("$(IP)/ipApp/Db/pzt.db","P=xxx:")
-### GP307 Vacuum Controller
-#dbLoadRecords("$(VME)/vmeApp/Db/gp307.db","P=xxx:")
-
### Queensgate Nano2k piezo controller
#dbLoadRecords("$(STD)/stdApp/Db/Nano2k.db","P=xxx:,S=s1")
-# Eurotherm temp controller
-#dbLoadRecords("$(IP)/ipApp/Db/Eurotherm.db","P=xxx:,C=0,SERVER=serial7")
-#devAoEurothermDebug=20
-
-# Analog I/O (Acromag IP330 ADC)
-dbLoadTemplate("ip330Scan.substitutions")
-
-# Machine-status board (MRD 100)
-#####################################################
-# dev32VmeConfig(card,a32base,nreg,iVector,iLevel)
-# card = card number
-# a32base = base address of card
-# nreg = number of A32 registers on this card
-# iVector = interrupt vector (MRD100 Only !!)
-# iLevel = interrupt level (MRD100 Only !!)
-# For Example
-# devA32VmeConfig(0, 0x80000000, 44, 0, 0)
-#####################################################
-# Configure the MSL MRD 100 module.....
-#devA32VmeConfig(0, 0xB0000200, 30, 0xa0, 5)
-
-#dbLoadRecords("$(STD)/stdApp/Db/msl_mrd101.db","C=0,S=01,ID1=01,ID2=01us")
-
### Bit Bus configuration
# BBConfig(Link, LinkType, BaseAddr, IrqVector, IrqLevel)
# Link: ?
# LinkType: 0:hosed; 1:xycom; 2:pep
#BBConfig(3,1,0x2400,0xac,5)
-# Set up the Allen-Bradley 6008 scanner
-#abConfigNlinks 1
-#abConfigVme 0,0xc00000,0x60,5
-#abConfigAuto
-
-# MKS vacuum gauges
-#dbLoadRecords("$(IP)/ipApp/Db/MKS.db","P=xxx:,C=0,SERVER=serial2,CC1=cc1,CC2=cc3,PR1=pr1,PR2=pr3")
-# PI Digitel 500/1500 pump
-#dbLoadRecords("$(IP)/ipApp/Db/Digitel.db","xxx:,PUMP=ip1,C=0,SERVER=serial3")
-# PI MPC ion pump
-#dbLoadRecords("$(IP)/ipApp/Db/MPC.db","P=xxx:,PUMP=ip2,C=0,SERVER=serial4,PA=0,PN=1")
-# PI MPC TSP (titanium sublimation pump)
-#dbLoadRecords("$(IP)/ipApp/Db/TSP.db","P=xxx:,TSP=tsp1,C=0,SERVER=serial4,PA=0")
-
-# APS Quad Electrometer from Steve Ross
-# initQuadEM(quadEMName, baseAddress, fiberChannel, microSecondsPerScan,
-# maxClients, unidigName, unidigChan)
-# quadEMName = name of quadEM object created
-# baseAddress = base address of VME card
-# fiberChannel = 0-3, fiber channel number
-# microSecondsPerScan = microseconds to integrate. When used with ipUnidig
-# interrupts the unit is also read at this rate.
-# maxClients = maximum number of clients that will connect to the
-# quadEM interrupt. 10 should be fine.
-# unidigName = name of ipInidig server if it is used for interrupts.
-# Set to 0 if there is no IP-Unidig being used, in which
-# case the quadEM will be read at 60Hz.
-# unidigChan = IP-Unidig channel connected to quadEM pulse output
-#initQuadEM("quadEM1", 0xf000, 0, 1000, 10, "Unidig1", 2)
-
-# initQuadEMScan(quadEMName, serverName, queueSize)
-# quadEMName = name of quadEM object created with initQuadEM
-# serverName = name of MPF server (string)
-# queueSize = size of MPF queue
-#initQuadEMScan("quadEM1", "quadEM1", 100)
-
-# initQuadEMSweep(quadEMName, serverName, maxPoints, int queueSize)
-# quadEMName = name of quadEM object created with initQuadEM
-# serverName = name of MPF server (string)
-# maxPoints = maximum number of channels per spectrum
-# queueSize = size of MPF queue
-#initQuadEMSweep("quadEM1", "quadEMSweep", 2048, 400)
-
-# initQuadEMPID(serverName, quadEMName, quadEMChannel,
-# DACName, DACChannel, queueSize)
-# serverName = name of MPF server (string)
-# quadEMName = name of quadEM object created with initQuadEM
-# quadEMChannel = quadEM "channel" to be used for feedback (0-9)
-# These are defined as:
-# 0 = current 1
-# 1 = current 2
-# 2 = current 3
-# 3 = current 4
-# 4 = sum 1 = current1 + current3
-# 5 = sum 2 = current2 + current4
-# 6 = difference 1 = current3 - current1
-# 7 = difference 2 = current4 - current2
-# 8 = position 1 = difference1/sum1 * 32767
-# 9 = position 2 = difference2/sum2 * 32767
-# DACName = name of DAC128V server created with initDAC128V
-# DACVChannel = DAC channel number used for this PID (0-7)
-# queueSize = size of MPF queue
-#initQuadEMPID("quadEMPID1", "quadEM1", 8, "DAC1", 2, 20)
-#initQuadEMPID("quadEMPID2", "quadEM1", 9, "DAC1", 3, 20)
-
-#Quad electrometer "scan" ai records
-#dbLoadRecords("$(QUADEM)/quadEMApp/Db/quadEM.db","P=xxx:, EM=EM1, CARD=0, SERVER=quadEM1")
-
-### APS Quad Electrometer in sweep mode
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=quadEM_1,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S0 @quadEMSweep")
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=quadEM_2,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S1 @quadEMSweep")
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=quadEM_3,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S2 @quadEMSweep")
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=quadEM_4,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S3 @quadEMSweep")
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=quadEM_5,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S8 @quadEMSweep")
-#dbLoadRecords("$(MCA)/mcaApp/Db/mca.db", "P=xxx:,M=quadEM_6,DTYPE=MPF MCA,NCHAN=2048,INP=#C0 S9 @quadEMSweep")
-
-# Fast feedback with IP330 and QuadEM
-#dbLoadTemplate("pid_fast.substitutions")
# Slow feedback
#dbLoadTemplate("pid_slow.substitutions")
-# CAMAC hardware
-# Setup the ksc2917 hardware definitions
-# These are all actually the defaults, so this is not really necessary
-# num_cards, addrs, ivec, irq_level
-#ksc2917_setup(1, 0xFF00, 0x00A0, 2)
-
-# Initialize the CAMAC library. Note that this is normally done automatically
-# in iocInit, but we need to get the CAMAC routines working before iocInit
-# because we need to initialize the DXP hardware.
-#camacLibInit
-
-### E500 Motors
-# E500 driver setup parameters:
-# (1) maximum # of controllers,
-# (2) maximum # axis per card
-# (3) motor task polling rate (min=1Hz, max=60Hz)
-#E500Setup(2, 8, 10)
-
-# E500 driver configuration parameters:
-# (1) controller
-# (2) branch
-# (3) crate
-# (4) slot
-#E500Config(0, 0, 0, 13)
-#E500Config(1, 0, 0, 14)
-
-### Scalers: CAMAC scaler
-# CAMACScalerSetup(int max_cards) /* maximum number of logical cards */
-#CAMACScalerSetup(1)
-
-# CAMACScalerConfig(int card, /* logical card */
-# int branch, /* CAMAC branch */
-# int crate, /* CAMAC crate */
-# int timer_type, /* 0=RTC-018 */
-# int timer_slot, /* Timer N */
-# int counter_type, /* 0=QS-450 */
-# int counter_slot) /* Counter N */
-#CAMACScalerConfig(0, 0, 0, 0, 20, 0, 21)
-#dbLoadRecords("$(CAMAC)/camacApp/Db/CamacScaler.db","P=xxx:,S=scaler1,C=0")
-#dbLoadRecords("$(STD)/stdApp/Db/scaler.db","P=xxx:,S=scaler1,C=0,DTYP=CAMAC scaler,FREQ=10000000")
-
-# Load the DXP stuff
-#< 16element_dxp.cmd
-
-# Generic CAMAC record
-#dbLoadRecords("$(CAMAC)/camacApp/Db/generic_camac.db","P=xxx:,R=camac1,SIZE=2048")
-
-### Etc. ###
-# Love Controllers
-#devLoveDebug=1
-#loveServerDebug=1
-#dbLoadRecords("$(IP)/ipApp/Db/love.db", "P=xxx:,Q=Love_0,C=0,PORT=PORT2,ADDR=1");
-
###############################################################################
# Set shell prompt (otherwise it is left at mv167 or mv162)
shellPromptSet "iocvxWorks> "