Something went wrong on our end
Code owners
Assign users and groups as approvers for specific file changes. Learn more.
st.cmd 8.38 KiB
# vxWorks startup script
sysVmeMapShow
# for vxStats
#putenv "engineer=not me"
#putenv "location=Earth"
engineer="not me"
location="Earth"
cd ""
< ../nfsCommands
< cdCommands
################################################################################
cd topbin
# If the VxWorks kernel was built using the project facility, the following must
# be added before any C++ code is loaded (see SPR #28980).
sysCplusEnable=1
# If using a PowerPC CPU with more than 32MB of memory, and not building with longjump, then
# allocate enough memory here to force code to load in lower 32 MB.
##mem = malloc(1024*1024*96)
### Load synApps EPICS software
ld < xxx.munch
cd startup
# Increase size of buffer for error logging from default 1256
errlogInit(20000)
# override address, interrupt vector, etc. information in module_types.h
#module_types()
# need more entries in wait/scan-record channel-access queue?
recDynLinkQsize = 1024
# Specify largest array CA will transport
# Note for N sscanRecord data points, need (N+1)*8 bytes, else MEDM
# plot doesn't display
putenv "EPICS_CA_MAX_ARRAY_BYTES=64008"
################################################################################
# Tell EPICS all about the record types, device-support modules, drivers,
# etc. in the software we just loaded (xxx.munch)
dbLoadDatabase("../../dbd/iocxxxVX.dbd")
iocxxxVX_registerRecordDeviceDriver(pdbbase)
# test pvHistory
#pvHistoryDebug = 1
#var pvHistoryDebug,1
dbLoadRecords("$(STD)/stdApp/Db/pvHistory.db","P=xxx:,N=1,MAXSAMPLES=1440")
### save_restore setup
# We presume a suitable initHook routine was compiled into xxx.munch.
# See also create_monitor_set(), after iocInit() .
< save_restore.cmd
# Industry Pack support
#< industryPack.cmd
# serial support
#< serial.cmd
# gpib support
#< gpib.cmd
# VME devices< vme.cmd
# CAMAC hardware
#<camac.cmd
# Motors
#dbLoadTemplate("basic_motor.substitutions")
dbLoadTemplate("motor.substitutions")
dbLoadTemplate("softMotor.substitutions")
#dbLoadTemplate("pseudoMotor.substitutions")
### Allstop, alldone
# This database must agree with the motors and other positioners you've actually loaded.
# Several versions (e.g., all_com_32.db) are in stdApp/Db
dbLoadRecords("$(STD)/stdApp/Db/all_com_16.db","P=xxx:")
### Insertion-device control
#dbLoadRecords("$(STD)/stdApp/Db/IDctrl.db","P=xxx:,xx=02us")
# sample-wheel
#dbLoadRecords("$(STD)/stdApp/Db/sampleWheel.db", "P=xxx:,ROWMOTOR=xxx:m7,ANGLEMOTOR=xxx:m8")
### Scan-support software
# crate-resident scan. This executes 1D, 2D, 3D, and 4D scans, and caches
# 1D data, but it doesn't store anything to disk. (See 'saveData' below for that.)
dbLoadRecords("$(SSCAN)/sscanApp/Db/scan.db","P=xxx:,MAXPTS1=8000,MAXPTS2=1000,MAXPTS3=10,MAXPTS4=10,MAXPTSH=8000")
# A set of scan parameters for each positioner. This is a convenience
# for the user. It can contain an entry for each scannable thing in the
# crate.
dbLoadTemplate("scanParms.substitutions")
### Slits
dbLoadRecords("$(OPTICS)/opticsApp/Db/2slit.db","P=xxx:,SLIT=Slit1V,mXp=m3,mXn=m4")
dbLoadRecords("$(OPTICS)/opticsApp/Db/2slit.db","P=xxx:,SLIT=Slit1H,mXp=m5,mXn=m6")
# under development...
#dbLoadRecords("$(OPTICS)/opticsApp/Db/2slit_soft.db","P=xxx:,SLIT=Slit2V,mXp=m13,mXn=m14")
#dbLoadRecords("$(OPTICS)/opticsApp/Db/2slit_soft.db","P=xxx:,SLIT=Slit2H,mXp=m15,mXn=m16")
# X-ray Instrumentation Associates Huber Slit Controller
# supported by a customized version of the SNL program written by Pete Jemian
#dbLoadRecords("$(OPTICS)/opticsApp/Db/xia_slit.db", "P=xxx:, HSC=hsc1:")
#dbLoadRecords("$(OPTICS)/opticsApp/Db/xia_slit.db", "P=xxx:, HSC=hsc2:")
#dbLoadRecords("$(IP)/ipApp/Db/generic_serial.db", "P=xxx:,C=0,SERVER=serial7")
### 2-post mirror
#dbLoadRecords("$(OPTICS)/opticsApp/Db/2postMirror.db","P=xxx:,Q=M1,mDn=m18,mUp=m17,LENGTH=0.3")
### User filters
#dbLoadRecords("$(OPTICS)/opticsApp/Db/filterMotor.db","P=xxx:,Q=fltr1:,MOTOR=m1,LOCK=fltr_1_2:")
#dbLoadRecords("$(OPTICS)/opticsApp/Db/filterMotor.db","P=xxx:,Q=fltr2:,MOTOR=m2,LOCK=fltr_1_2:")
#dbLoadRecords("$(OPTICS)/opticsApp/Db/filterLock.db","P=xxx:,Q=fltr2:,LOCK=fltr_1_2:,LOCK_PV=xxx:DAC1_1.VAL")
### Optical tables
#tableRecordDebug=1
putenv "DIR=$(OPTICS)/opticsApp/Db"
dbLoadRecords("$(DIR)/table.db","P=xxx:,Q=Table1,T=table1,M0X=m1,M0Y=m2,M1Y=m3,M2X=m4,M2Y=m5,M2Z=m6,GEOM=SRI")
### Monochromator support ###
# Kohzu and PSL monochromators: Bragg and theta/Y/Z motors
# standard geometry (geometry 1)
#dbLoadRecords("$(OPTICS)/opticsApp/Db/kohzuSeq.db","P=xxx:,M_THETA=m9,M_Y=m10,M_Z=m11,yOffLo=17.4999,yOffHi=17.5001")
# modified geometry (geometry 2)
#dbLoadRecords("$(OPTICS)/opticsApp/Db/kohzuSeq.db","P=xxx:,M_THETA=m9,M_Y=m10,M_Z=m11,yOffLo=4,yOffHi=36")
# Spherical grating monochromator
#dbLoadRecords("$(OPTICS)/opticsApp/Db/SGM.db","P=xxx:,N=1,M_x=m7,M_rIn=m6,M_rOut=m8,M_g=m9")
# 4-bounce high-resolution monochromator
#dbLoadRecords("$(OPTICS)/opticsApp/Db/hrSeq.db","P=xxx:,N=1,M_PHI1=m9,M_PHI2=m10")
#dbLoadRecords("$(OPTICS)/opticsApp/Db/hrSeq.db","P=xxx:,N=2,M_PHI1=m11,M_PHI2=m12")
### Orientation matrix, four-circle diffractometer (see seq program 'orient' below)
dbLoadRecords("$(OPTICS)/opticsApp/Db/orient.db", "P=xxx:,O=1,PREC=4")
dbLoadRecords("$(OPTICS)/opticsApp/Db/orient.db", "P=xxx:,O=2,PREC=4")
dbLoadTemplate("orient_xtals.substitutions")
# Load single element Canberra AIM MCA and ICB modules
#< canberra_1.cmd
# Load 13 element detector software
#< canberra_13.cmd
# Load 3 element detector software
#< canberra_3.cmd
### Stuff for user programming ###
dbLoadRecords("$(CALC)/calcApp/Db/userCalcs10.db","P=xxx:")
dbLoadRecords("$(CALC)/calcApp/Db/userCalcOuts10.db","P=xxx:")
dbLoadRecords("$(CALC)/calcApp/Db/userStringCalcs10.db","P=xxx:")
dbLoadRecords("$(CALC)/calcApp/Db/userTransforms10.db","P=xxx:")
# extra userCalcs (must also load userCalcs10.db for the enable switch)
dbLoadRecords("$(CALC)/calcApp/Db/userCalcN.db","P=xxx:,N=I_Detector")
dbLoadRecords("$(CALC)/calcApp/Db/userAve10.db","P=xxx:")
# string sequence (sseq) record
dbLoadRecords("$(STD)/stdApp/Db/yySseq.db","P=xxx:,S=Sseq1")
dbLoadRecords("$(STD)/stdApp/Db/yySseq.db","P=xxx:,S=Sseq2")
dbLoadRecords("$(STD)/stdApp/Db/yySseq.db","P=xxx:,S=Sseq3")
# 4-step measurement
dbLoadRecords("$(STD)/stdApp/Db/4step.db", "P=xxx:")
# interpolation
dbLoadRecords("$(CALC)/calcApp/Db/interp.db", "P=xxx:,N=2000")
# array test
dbLoadRecords("$(CALC)/calcApp/Db/arrayTest.db", "P=xxx:,N=2000")
# Slow feedback
dbLoadTemplate "pid_slow.substitutions"
# Miscellaneous PV's, such as burtResult
dbLoadRecords("$(STD)/stdApp/Db/misc.db","P=xxx:")
#dbLoadRecords("$(STD)/stdApp/Db/VXstats.db","P=xxx:")
# vxStats
dbLoadTemplate("vxStats.substitutions")
### Queensgate piezo driver
#dbLoadRecords("$(IP)/ipApp/Db/pzt_3id.db","P=xxx:")
#dbLoadRecords("$(IP)/ipApp/Db/pzt.db","P=xxx:")
### Queensgate Nano2k piezo controller
#dbLoadRecords("$(STD)/stdApp/Db/Nano2k.db","P=xxx:,S=s1")
###############################################################################
# Set shell prompt (otherwise it is left at mv167 or mv162)
shellPromptSet "iocvxWorks> "
iocLogDisable=0
iocInit
### startup State Notation Language programs
#seq &kohzuCtl, "P=xxx:, M_THETA=m9, M_Y=m10, M_Z=m11, GEOM=2, logfile=kohzuCtl.log"
#seq &hrCtl, "P=xxx:, N=1, M_PHI1=m9, M_PHI2=m10, logfile=hrCtl1.log"
# Keithley 2000 series DMM
# channels: 10, 20, or 22; model: 2000 or 2700
#seq &Keithley2kDMM,("P=xxx:, Dmm=D1, channels=22, model=2700")
#seq &Keithley2kDMM,("P=xxx:, Dmm=D2, channels=10, model=2000")
# Bunch clock generator
#seq &getFillPat, "unit=xxx"
# X-ray Instrumentation Associates Huber Slit Controller
# supported by a SNL program written by Pete Jemian and modified (TMM) for use with the
# sscan record
#seq &xia_slit, "name=hsc1, P=xxx:, HSC=hsc1:, S=xxx:seriala[6]"
# Orientation-matrix
#orientDebug=1
seq &orient, "P=xxx:orient1:,PM=xxx:,mTTH=m9,mTH=m10,mCHI=m11,mPHI=m12"
seq &orient, "P=xxx:orient2:,PM=xxx:,mTTH=m13,mTH=m14,mCHI=m15,mPHI=m16"
### Start up the autosave task and tell it what to do.
# The task is actually named "save_restore".
# Note that you can reload these sets after creating them: e.g.,
# reload_monitor_set("auto_settings.req",30,"P=xxx:")
#save_restoreDebug=20
#
# save positions every five seconds
create_monitor_set("auto_positions.req",5,"P=xxx:")
# save other things every thirty seconds
create_monitor_set("auto_settings.req",30,"P=xxx:")
### Start the saveData task.
saveData_Init("saveData.req", "P=xxx:")
# If memory allocated at beginning free it now
##free(mem)
dbcar(0,1)