changes to comply with tyGSAsynInit()'s new argument list

begin/end comments

iocBoot/iocvxWorks/serial.cmd

-###############################################################################
+
+# BEGIN serial.cmd ------------------------------------------------------------
+
 # Initialize Octal UART stuff
 # tyGSOctalDrv(int maxModules)
 tyGSOctalDrv(1)
@@ -12,16 +14,17 @@ tyGSOctalDrv(1)
 # slot    - location of module on carrier -- 0..3 for slot A..slot D
 tyGSOctalModuleInit("UART_0", "232", 0x80, 0, 0)
 
-# int tyGSAsynInit(char *port, char *moduleName, int channel, int baud, char parity, int sbits,
-#                  int dbits, char handshake, char *eomstr)
-tyGSAsynInit("serial1",  "UART_0", 0, 9600,'N',2,8,'N',"")  /* SRS570 */
-tyGSAsynInit("serial2",  "UART_0", 1,19200,'E',1,8,'N',"")  /* MKS */
-tyGSAsynInit("serial3",  "UART_0", 2, 9600,'E',1,7,'N',"")  /* Digitel */
-tyGSAsynInit("serial4",  "UART_0", 3, 9600,'N',1,8,'N',"")  /* MPC */
-tyGSAsynInit("serial5",  "UART_0", 4, 9600,'E',1,7,'N',"")  /* McClennan PM304 */
-tyGSAsynInit("serial6",  "UART_0", 5,19200,'N',1,8,'N',"")  /* Keithley 2000 */
-tyGSAsynInit("serial7",  "UART_0", 6, 9600,'N',1,8,'N',"")  /* Oxford ILM cryometer */
-tyGSAsynInit("serial8",  "UART_0", 7,19200,'N',1,8,'N',"")  /* Love controllers */
+# int tyGSAsynInit(char *port, char *moduleName, int channel, int baud,
+# char parity, int sbits, int dbits, char handshake, 
+# char *inputEos, char *outputEos)
+tyGSAsynInit("serial1",  "UART_0", 0, 9600,'N',2,8,'N',"","")  /* SRS570 */
+tyGSAsynInit("serial2",  "UART_0", 1,19200,'E',1,8,'N',"","")  /* MKS */
+tyGSAsynInit("serial3",  "UART_0", 2, 9600,'E',1,7,'N',"","")  /* Digitel */
+tyGSAsynInit("serial4",  "UART_0", 3, 9600,'N',1,8,'N',"","")  /* MPC */
+tyGSAsynInit("serial5",  "UART_0", 4, 9600,'E',1,7,'N',"","")  /* McClennan PM304 */
+tyGSAsynInit("serial6",  "UART_0", 5,19200,'N',1,8,'N',"","")  /* Keithley 2000 */
+tyGSAsynInit("serial7",  "UART_0", 6, 9600,'N',1,8,'N',"","")  /* Oxford ILM cryometer */
+tyGSAsynInit("serial8",  "UART_0", 7,19200,'N',1,8,'N',"","")  /* Love controllers */
 
 # Newport MM4000 driver setup parameters:
 #     (1) maximum # of controllers,
@@ -130,3 +133,4 @@ dbLoadRecords("$(IP)/ipApp/Db/SR570.db", "P=xxx:,A=A1,PORT=serial1")
 #loveServerDebug=1
 #dbLoadRecords("$(IP)/ipApp/Db/love.db", "P=xxx:,Q=Love_0,C=0,PORT=PORT2,ADDR=1")
 
+# END serial.cmd --------------------------------------------------------------